View PD46364185BF1-E40-EQ1_7095390.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

r10ds0092ej0400 rev.4.00 page 1 of 34 nov 09, 2012 datasheet pd46364185b pd46364365b 36m-bit ddr ii sram separate i/o 2-word burst operation description the pd46364185b is a 2,097,152-word by 18-bit and the pd46364365b is a 1,048,576-word by 36-bit synchronous double data rate static ram fabricated with advanced cmos technology using full cmos six-transistor memory cell. the pd46364185b and pd46364365b integrate unique synchronous peripheral circuitry and a burst counter. all input registers controlled by an input clock pair (k and k#) are latched on the positive edge of k and k#. these products are suitable for application which require synchronous operation, high speed, low voltage, high density and wide bit configuration. these products are packaged in 165-pin plastic bga. features ? 1.8 0.1 v power supply ? 165-pin plastic bga (13 x 15) ? hstl interface ? pll circuitry for wide output data valid window and future frequency scaling ? separate independent read and write data ports ? ddr read or write ope ration initiated each cycle ? pipelined double data rate operation ? separate data input/output bus ? two-tick burst for low ddr transaction size ? two input clocks (k and k#) for precise ddr timing at clock rising edges only ? two output clocks (c and c#) for precise flight time and clock skew matching-clock and data delivered together to receiving device ? internally self-timed write control ? clock-stop capability. normal operation is restored in 20 s after clock is resumed. ? user programmable impedance output (35 to 70 ) ? fast clock cycle time : 3.3 ns (300 mhz), 4.0 ns (250 mhz) ? simple control logic for easy depth expansion ? jtag 1149.1 compatible test access port r10ds0092ej0400 rev.4.00 nov 09, 2012
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 2 of 34 nov 09, 2012 ordering information part no. organization (word x bit) cycle time clock frequency core supply voltage operating ambient temperature package pd46364185bf1-e33-eq1-a 2m x 18 3.3ns 300mhz 1.8 0.1 t a = 0 to 70 c 165-pin PD46364185BF1-E40-EQ1-a 4.0ns 250mhz plastic pd46364365bf1-e33-eq1-a 1m x 36 3.3ns 300mhz bga pd46364365bf1-e40-eq1-a 4.0ns 250mhz (13 x 15) pd46364185bf1-e33y-eq1-a 2m x 18 3.3ns 300mhz 1.8 0.1 t a = -40 to 85 c lead-free pd46364185bf1-e40y-eq1-a 4.0ns 250mhz pd46364365bf1-e33y-eq1-a 1m x 36 3.3ns 300mhz pd46364365bf1-e40y-eq1-a 4.0ns 250mhz pd46364185bf1-e33-eq1 2m x 18 3.3ns 300mhz 1.8 0.1 t a = 0 to 70 c 165-pin PD46364185BF1-E40-EQ1 4.0ns 250mhz plastic pd46364365bf1-e33-eq1 1m x 36 3.3ns 300mhz bga pd46364365bf1-e40-eq1 4.0ns 250mhz (13 x 15) pd46364185bf1-e33y-eq1 2m x 18 3.3ns 300mhz 1.8 0.1 t a = -40 to 85 c lead pd46364185bf1-e40y-eq1 4.0ns 250mhz pd46364365bf1-e33y-eq1 1m x 36 3.3ns 300mhz pd46364365bf1-e40y-eq1 4.0ns 250mhz
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 3 of 34 nov 09, 2012 pin arrangement 165-pin plastic bga (13 x 15) (top view) [ pd46364185b] 2m x 18 1 2 3 4 5 6 7 8 9 10 11 a cq# v ss /144m a r, w# bw1# k# nc/288m ld# a v ss /72m cq b nc q9 d9 a nc k bw0# a nc nc q8 c nc nc d10 v ss a a a v ss nc q7 d8 d nc d11 q10 v ss v ss v ss v ss v ss nc nc d7 e nc nc q11 v dd q v ss v ss v ss v dd qnc d6 q6 f nc q12 d12 v dd q v dd v ss v dd v dd qnc nc q5 g nc d13 q13 v dd q v dd v ss v dd v dd q nc nc d5 h dll# v ref v dd q v dd q v dd v ss v dd v dd qv dd q v ref zq j nc nc d14 v dd q v dd v ss v dd v dd qnc q4 d4 k nc nc q14 v dd q v dd v ss v dd v dd qnc d3 q3 l nc q15 d15 v dd q v ss v ss v ss v dd qnc nc q2 m nc nc d16 v ss v ss v ss v ss v ss nc q1 d2 n nc d17 q16 v ss a a a v ss nc nc d1 p nc nc q17 a a c a a nc d0 q0 r tdo tck a a a c# a a a tms tdi a : address inputs tms : ieee 1149.1 test input d0 to d17 : data inputs tdi : ieee 1149.1 test input q0 to q17 : data outputs tc k : ieee 1149.1 clock input ld# : synchronous load tdo : ieee 1149.1 test output r, w# : read write input v ref : hstl input reference input bw0#, bw1# : byte write data select v dd : power supply k, k# : input clock v dd q : power supply c, c# : output clock v ss : ground cq, cq# : echo clock nc : no connection zq : output impedance matching nc/xxm : expansion address for xxmb dll# : pll disable remarks 1. # indicates active low. 2. refer to package dimensions for the index mark. 3. 2a, 7a and 10a are expansion addresses : 10a for 72mb : 10a and 2a for 144mb : 10a, 2a and 7a for 288mb 2a and 10a of this product can also be used as nc.
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 4 of 34 nov 09, 2012 pin arrangement 165-pin plastic bga (13 x 15) (top view) [ pd46364365b] 1m x 36 1 2 3 4 5 6 7 8 9 10 11 a cq# v ss /288m nc/72m r, w# bw2# k# bw1# ld# a v ss /144m cq b q27 q18 d18 a bw3# k bw0# a d17 q17 q8 c d27 q28 d19 v ss a a a v ss d16 q7 d8 d d28 d20 q19 v ss v ss v ss v ss v ss q16 d15 d7 e q29 d29 q20 v dd q v ss v ss v ss v dd q q15 d6 q6 f q30 q21 d21 v dd q v dd v ss v dd v dd q d14 q14 q5 g d30 d22 q22 v dd q v dd v ss v dd v dd q q13 d13 d5 h dll# v ref v dd q v dd q v dd v ss v dd v dd qv dd q v ref zq j d31 q31 d23 v dd q v dd v ss v dd v dd qd12 q4 d4 k q32 d32 q23 v dd q v dd v ss v dd v dd q q12 d3 q3 l q33 q24 d24 v dd q v ss v ss v ss v dd q d11 q11 q2 m d33 q34 d25 v ss v ss v ss v ss v ss d10 q1 d2 n d34 d26 q25 v ss a a a v ss q10 d9 d1 p q35 d35 q26 a a c a a q9 d0 q0 r tdo tck a a a c# a a a tms tdi a : address inputs dll# : pll disable d0 to d35 : data inputs tms : ieee 1149.1 test input q0 to q35 : data outputs td i : ieee 1149.1 test input ld# : synchronous load tck : ieee 1149.1 clock input r, w# : read write input t do : ieee 1149.1 test output bw0# to bw3# : byte write data select v ref : hstl input reference input k, k# : input clock v dd : power supply c, c# : output clock v dd q : power supply cq, cq# : echo clock v ss : ground zq : output impedance matching nc : no connection remarks 1. # indicates active low. 2. refer to package dimensions for the index mark. 3. 2a, 3a and 10a are expansion addresses: 3a for 72mb : 3a and 10a for 144mb : 3a, 10a and 2a for 288mb 2a and 10a of this product can also be used as nc.
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 5 of 34 nov 09, 2012 pin description (1/2) symbol type description a input synchronous address inputs: these inputs are r egistered and must meet the setup and hold times around the rising edge of k. all tran sactions operate on a burst of two words (one clock period of bus activity). these inputs ar e ignored when device is deselected, i.e., nop (ld# = high). d0 to dxx input synchronous data inputs: input data must meet setup and hold times around the rising edges of k and k# during write operations. see pin arrangement for ball site location of individual signals. x18 device uses d0 to d17. x36 device uses d0 to d35. q0 to qxx output synchronous data outputs: out put data is synchronized to the respective c and c# or to k and k# rising edges if c and c# are tied high. data is output in synchronization with c and c# (or k and k#), depending on the ld# and r, w# command. see pin arrangement for ball site location of individual signals. x18 device uses q0 to q17. x36 device uses q0 to q35. ld# input synchronous load: this input is brought low when a bus cycle sequence is to be defined. this definition includes address and read/write direction. all transactions operate on a burst of 2 data (one clock period of bus activity). r, w# input synchronous read/write input: when ld# is lo w, this input designates the access type (read when r, w# is high, write when r, w# is low) for the loaded address. r, w# must meet the setup and hold ti mes around the rising edge of k. bwx# input synchronous byte writes: when low these in puts cause their respective byte to be registered and written during write cycles. t hese signals must meet setup and hold times around the rising edges of k and k# for each of the two rising edges comprising the write cycle. see pin arrangement for signal to data relationships. x18 device uses bw0#, bw1#. x36 device uses bw0# to bw3#. see byte write operation for relation between bwx# and dxx. k, k# input input clock: this input clock pair registers a ddress and control inputs on the rising edge of k, and registers data on the rising edge of k and the rising edge of k#. k# is ideally 180 degrees out of phase with k. all synchronous in puts must meet setup and hold times around the clock rising edges. c, c# input output clock: this clock pair provides a user controlled means of tuning device output data. the rising edge of c# is used as the output timi ng reference for first output data. the rising edge of c is used as the output reference for se cond output data. ideally, #c is 180 degrees out of phase with c. when use of k and k# as the reference instead of c and c#, then fixed c and c# to high. operation cannot be g uaranteed unless c and c# are fixed to high (i.e. toggle of c and c#)
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 6 of 34 nov 09, 2012 (2/2) symbol type description cq, cq# output synchronous echo clock outputs. the rising ed ges of these outputs are tightly matched to the synchronous data outputs and can be used as a data valid indication. these signals run freely and do not stop when q tristates. if c and c# are stopped (if k and k# are stopped in the single clock mode), cq and cq# will also stop. zq input output impedance matching input: this inpu t is used to tune the device outputs to the system data bus impedance. q, cq and cq# out put impedance are set to 0.2 x rq, where rq is a resistor from this bump to grou nd. the output impedance can be minimized by directly connect zq to v dd q. this pin cannot be connected directly to gnd or left unconnected. the output impeda nce is adjusted every 20 s upon power-up to account for drifts in supply voltage and temperature. afte r replacement for a resistor, the new output impedance is reset by implementing power-on sequence. dll# input pll disable: when debugging the system or board, the operation c an be performed at a clock frequency slower than tkhkh (max.) without the pll circuit being used, if dll# = low. the ac/dc characteristics cannot be guar anteed. for normal operation, dll# must be high and it can be connected to v dd q through a 10 k or less resistor. tms tdi input ieee 1149.1 test inputs: 1.8 v i/ o level. these balls may be left not connected if the jtag function is not used in the circuit. tck input ieee 1149.1 clock input: 1.8 v i/o leve l. this pin must be tied to v ss if the jtag function is not used in the circuit. tdo output ieee 1149.1 test output: 1.8 v i/o level. when providing any external voltage to tdo signal, it is recommended to pull up to v dd . v ref ? hstl input reference voltage: nominally v dd q/2. provides a reference voltage for the input buffers. v dd supply power supply: 1.8 v nominal. see recommended dc operating conditions and dc characteristics for range. v dd q supply power supply: isolated output buffer supply. nominally 1.5 v. 1.8 v is also permissible. see recommended dc operating conditions and dc characteristics for range. v ss supply power supply: ground nc ? no connect: these signals are not connected internally.
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 7 of 34 nov 09, 2012 block diagram [ pd46364185b] [ pd46364365b] r, w# bw0# bw1# ld# k k# k ld# r, w# k address 20 d0 to d17 q0 to q17 mux output register k# k data registry & logic 2 20 x 36 memory array write driver sense amps output select output buffer 20 address registry & logic write register c, c# or k, k# cq, cq# 18 36 36 36 18 2 r, w# bw0# bw1# ld# k k# k ld# r, w# k address 19 d0 to d35 q0 to q35 mux output register k# k data registry & logic 2 19 x 72 memory array write driver sense amps output select output buffer 19 address registry & logic write register c, c# or k, k# cq, cq# 36 72 72 72 36 2 bw2# bw3#
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 8 of 34 nov 09, 2012 power-on sequence in ddr ii sram ddr ii srams must be powered up and initialized in a predefined manner to prevent undefined operations. the following timing charts show the recommended power-on sequence. the following power-up supply voltage application is recommended: v ss , v dd , v dd q, v ref , then v in . v dd and v dd q can be applied simultaneously, as long as v dd q does not exceed v dd by more than 0.5 v during power-up. the following power-down supply voltage removal sequence is recommended: v in , v ref , v dd q, v dd , v ss . v dd and v dd q can be removed simultaneously, as long as v dd q does not exceed v dd by more than 0.5 v during power-down. power-on sequence apply power and tie dll# to high. apply v dd q before v ref or at the same time as v ref . provide stable clock for more than 20 s to lock the pll. continuous min.4 nop(ld# = high) cycles are required after pll lock up is done. pll constraints the pll uses k clock as its synchronizing input and the in put should have low phase jitter which is specified as tkc var. the pll can cover 120 mhz as the lowest freq uency. if the input clock is unstable and the pll is enabled, then the pll may lock onto an undesired clock frequency. power-on waveforms 20 s or more stable clock v dd /v dd q stable (< 0.1 v dc per 50 ns) v dd /v dd q clock unstable clock normal operation start dll# fix high (or tied to v dd q) ld# 4 times nop
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 9 of 34 nov 09, 2012 truth table operation ld# r, w# clk d or q write cycle l l l h data in load address, input write data on input data d(a+0) d(a+1) consecutive k and k# rising edge input clock k(t+1) k#(t+1) read cycle l h l h data out load address, read data on output data q(a+0) q(a+1) consecutive c and c# rising edge output clock c#(t+1) c(t+2) nop (no operation) h l hd = , q = high-z clock stop stopped previous state remarks 1. h : high, l : low, : don?t care, : rising edge. 2. data inputs are registered at k and k# rising edges. data outputs are delivered at c and c# rising edges except if c and c# are high th en data outputs are delivered at k and k# rising edges. 3. all control inputs in the truth table must meet set up/hold times around the rising edge (low to high) of k. all control inputs are registered during the rising edge of k. 4. this device contains circuitry that ensure the outputs to be in high impedance during power-up. 5. refer to state diagram and timi ng diagrams for clarification. 6. it is recommended that k = k# = c = c# when clock is stopped. this is not essential but permits most rapid restart by overcoming transmission line charging symmetrically.
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 10 of 34 nov 09, 2012 byte write operation [ pd46364185b] operation k k# bw0# bw1# write d0 to d17 l h ? 0 0 ? l h 0 0 write d0 to d8 l h ? 0 1 ? l h 0 1 write d9 to d17 l h ? 1 0 ? l h 1 0 write nothing l h ? 1 1 ? l h 1 1 remarks 1. h : high, l : low, : rising edge. 2. assumes a write cycle was initiated. bw0# and bw1# can be altered for any portion of the burst write operation provided that the setu p and hold requirements are satisfied. [ pd46364365b] operation k k# bw0# bw1# bw2# bw3# write d0 to d35 l h ? 0 0 0 0 ? l h 0 0 0 0 write d0 to d8 l h ? 0 1 1 1 ? l h 0 1 1 1 write d9 to d17 l h ? 1 0 1 1 ? l h 1 0 1 1 write d18 to d26 l h ? 1 1 0 1 ? l h 1 1 0 1 write d27 to d35 l h ? 1 1 1 0 ? l h 1 1 1 0 write nothing l h ? 1 1 1 1 ? l h 1 1 1 1 remarks 1. h : high, l : low, : rising edge. 2. assumes a write cycle was initiated. bw0# to bw 3# can be altered for any portion of the burst write operation provided that the setu p and hold requirements are satisfied.
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 11 of 34 nov 09, 2012 bus cycle state diagram remark state machine control timing se quence is controlled by k. read double count = count + 2 write double count = count + 2 power up write nop supply voltage provided load new address count = 0 nop load, count = 2 read load, count = 2 load nop, count = 2 nop, count = 2
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 12 of 34 nov 09, 2012 electrical characteristics absolute maximum ratings parameter symbol conditions rating unit supply voltage v dd ? 0.5 to + 2.5 v output supply voltage v dd q ? 0.5 to v dd v input voltage v in ? 0.5 to v dd + 0.5 (2.5 v max.) v input / output voltage v i/o ? 0.5 to v dd q + 0.5 (2.5 v max.) v operating ambient temperature t a (e** series) 0 to 70 c (e**y series) -40 to 85 c storage temperature t stg ? 55 to + 125 c caution exposing the device to stress above those listed in absolute maximum ratings could cause permanent damage. the device is not meant to be operated under conditions outside the limits described in the operational section of this speci fication. exposure to absolute maximum rating conditions for extended periods may affect device reliability. recommended dc operating conditions (t a = 0 to 70 c, t a = -40 to 85 c) parameter symbol conditions min. typ. max. unit note supply voltage v dd 1.7 1.8 1.9 v output supply voltage v dd q 1.4 v dd v 1 input high voltage v ih (dc) v ref + 0.1 v dd q + 0.3 v 1, 2 input low voltage v il (dc) ? 0.3 v ref ? 0.1 v 1, 2 clock input voltage v in ? 0.3 v dd q + 0.3 v 1, 2 reference voltage v ref 0.68 0.95 v notes 1. during normal operation, v dd q must not exceed v dd . 2. power-up: vih v dd q + 0.3 v and v dd 1.7 v and v dd q 1.4 v for t 200 ms recommended ac operating conditions (t a = 0 to 70 c, t a = -40 to 85 c) parameter symbol conditions min. max. unit note input high voltage v ih (ac) v ref + 0.2 v 1 input low voltage v il (ac) v ref ? 0.2 v 1 note 1. overshoot: v ih (ac) v dd + 0.7 v (2.5 v max.) for t tkhkh/2 undershoot: v il (ac) ? 0.5 v for t tkhkh/2 control input signals may not have pulse widths less th an tkhkl (min.) or operate at cycle rates less than tkhkh (min.).
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 13 of 34 nov 09, 2012 dc characteristics 1 (t a = 0 to 70 c, v dd = 1.8 0.1 v) parameter symbol test condition min. max. unit note x18 x36 input leakage current i li ? 2 + 2 a i/o leakage current i lo ? 2 + 2 a operating supply current i dd v in v il or v in v ih , -e33 530 600 ma (read cycle / write cycle) i i/o = 0 ma, cycle = max. -e40 480 540 standby supply current i sb1 v in v il or v in v ih , -e33 400 420 ma (nop) i i/o = 0 ma, cycle = max. -e40 380 390 inputs static output high voltage v oh(low) |i oh | 0.1 ma v dd q ? 0.2 v dd q v 3, 4 v oh note1 v dd q/2 ? 0.12 v dd q/2 + 0.12 v 3, 4 output low voltage v ol(low) i ol 0.1 ma v ss 0.2 v 3, 4 v ol note2 v dd q/2 ? 0.12 v dd q/2 + 0.12 v 3, 4 notes 1. outputs are impedance-controlled. | i oh | = (v dd q/2)/(rq/5) 15% for values of 175 rq 350 . 2. outputs are impedance-controlled. i ol = (v dd q/2)/(rq/5) 15% for values of 175 rq 350 . 3. ac load current is higher than the shown dc values. 4. hstl outputs meet jedec hstl class i standards.
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 14 of 34 nov 09, 2012 dc characteristics 2 (t a = -40 to 85 c, v dd = 1.8 0.1 v) parameter symbol test condition min. max. unit note x18 x36 input leakage current i li ? 2 + 2 a i/o leakage current i lo ? 2 + 2 a operating supply current i dd v in v il or v in v ih , -e33y 680 760 ma (read cycle / write cycle) i i/o = 0 ma, cycle = max. -e40y 630 690 standby supply current i sb1 v in v il or v in v ih , -e33y 530 550 ma (nop) i i/o = 0 ma, cycle = max. -e40y 500 520 inputs static output high voltage v oh(low) |i oh | 0.1 ma v dd q ? 0.2 v dd q v 3, 4 v oh note1 v dd q/2 ? 0.12 v dd q/2 + 0.12 v 3, 4 output low voltage v ol(low) i ol 0.1 ma v ss 0.2 v 3, 4 v ol note2 v dd q/2 ? 0.12 v dd q/2 + 0.12 v 3, 4 notes 1. outputs are impedance-controlled. | i oh | = (v dd q/2)/(rq/5) 15% for values of 175 rq 350 . 2. outputs are impedance-controlled. i ol = (v dd q/2)/(rq/5) 15% for values of 175 rq 350 . 3. ac load current is higher than the shown dc values. 4. hstl outputs meet jedec hstl class i standards.
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 15 of 34 nov 09, 2012 capacitance (t a = 25 c, f = 1 mhz) parameter symbol test conditions min. max. unit input capacitance c in v in = 0 v 5 pf (address, control) input / output capacitance c i/o v i/o = 0 v 7 pf (d, q, cq, cq#) clock input capacitance c clk v clk = 0 v 6 pf remark these parameters are periodically sampled and not 100% tested. thermal characteristics parameter symbol substrate airflow typ. unit thermal resistance ja 4-layer 0 m/s 16.5 c/w from junction to ambient air 1 m/s 13.2 c/w 8-layer 0 m/s 15.5 c/w 1 m/s 12.6 c/w thermal characterization parameter jt 4-layer 0 m/s 0.07 c/w from junction to the top center 1 m/s 0.13 c/w of the package surface 8-layer 0 m/s 0.06 c/w 1 m/s 0.12 c/w thermal resistance jc 3.86 c/w from junction to case
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 16 of 34 nov 09, 2012 ac characteristics (t a = 0 to 70 c, t a = -40 to 85 c, v dd = 1.8 0.1 v) ac test conditions (v dd = 1.8 0.1 v, v dd q = 1.4 v to v dd ) input waveform (rise / fall time 0.3 ns) 0.75 v 0.75 v test points 1.25 v 0.25 v output waveform v dd q / 2 v dd q / 2 test points output load condition figure 1. external load at test v dd q / 2 0.75 v 50 z o = 50 250 sram v ref zq
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 17 of 34 nov 09, 2012 read and write cycle parameter symbol -e33,-e33y -e40,-e40y unit note (300 mhz) (250 mhz) min. max. min. max. clock average clock cycle time tkhkh 3.3 8.4 4.0 8.4 ns 1 (k, k#, c, c#) clock phase jitter (k, k#, c, c#) tkc var 0.2 0.2 ns 2 clock high time (k, k#, c, c#) tkhkl 1.32 1.6 ns clock low time (k, k#, c, c#) tklkh 1.32 1.6 ns clock high to clock# high tkhk#h 1.49 1.8 ns (k k#, c c#) clock# high to clock high tk#hkh 1.49 1.8 ns (k# k, c# c) clock to data clock tkhch 0 1.45 0 1.8 ns (k c, k# c#) pll lock time (k, c) tkc lock 20 20 output times cq high to cq# high tcqhcq#h 1.24 1.55 ns 5 (cq cq#) cq# high to cq high tcq#hcqh 1.24 1.55 ns 5 (cq# cq) c, c# high to output valid tchqv 0.45 0.45 ns c, c# high to output hold tchqx ? 0.45 ? 0.45 ns c, c# high to echo clock valid tchcqv 0.45 0.45 ns c, c# high to echo clock hold tchcqx ? 0.45 ? 0.45 ns cq, cq# high to output valid tcqhqv 0.27 0.3 ns 6 cq, cq# high to output hold tcqhqx ? 0.27 ? 0.3 ns 6 c high to output high-z tchqz 0.45 0.45 ns c high to output low-z tchqx1 ? 0.45 ? 0.45 ns setup times address valid to k rising e dge tavkh 0.4 0.5 ns 7 synchronous load input (ld#), tivkh 0.4 0.5 ns 7 read write input (r, w#) valid to k rising edge data inputs and write data tdvkh 0.3 0.35 ns 7 select inputs (bwx#) valid to k, k# rising edge hold times k rising edge to address hold tkhax 0.4 0.5 ns 7 k rising edge to tkhix 0.4 0.5 ns 7 synchronous load input (ld#), read write input (r, w#) hold k, k# rising edge to data inputs tkhdx 0.3 0.35 ns 7 and write data select inputs (bwx#) hold
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 18 of 34 nov 09, 2012 notes 1. when debugging the system or board, these products can operate at a clock fre quency slower than tkhkh (max.) without the pll circuit being used, if dll# = low. read latency (rl) is changed to 1.0 clock cycle in this operation. the ac/dc characteristics cannot be guaranteed, however. 2. clock phase jitter is the variance from clock rising e dge to the next expected clock rising edge. tkc var (max.) indicates a peak-to-peak value. 3. v dd slew rate must be less than 0.1 v dc per 50 ns for pll lock retention. pll lock time begins once v dd and input clock are stable. it is recommended that the device is kept nop (ld# = high) during these cycles. 4. k input is monitored for this operation. see below for the timing. k k tkc reset or tkc reset 5. guaranteed by design. 6. echo clock is very tightly controlled to data valid / data hold. by design, there is a 0.1 ns variation from echo clock to data. the data sheet parameters reflect tester guardbands and test setup variations. 7. this is a synchronous device. all addresses, data an d control lines must meet th e specified setup and hold times for all latching clock edges. remarks 1. this parameter is sampled. 2. test conditions as specified with the output loadin g as shown in ac test conditions unless otherwise noted. 3. control input signals may not be operated with pulse widths less than tkhkl (min.). 4. if c, c# are tied high, k, k# become the references for c, c# timing parameters. 5. v dd q is 1.5 v dc.
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 19 of 34 nov 09, 2012 read and write timing k address data in k# 2468 13 5 7 tkhk#h c c# tkhch nop read (burst of 2) write (burst of 2) tkhkl tklkh q00 q10 data out q01 q11 ld# r, w# tkhch tkhkl tklkh tkhk#h tk#hkh tchqx1 tchqx tchqz d21 tdvkh tkhdx tdvkh tkhdx tkhkh tivkh tkhix tavkh tkhax cq cq# tcqhqv tcqhqx tchqv tchcqx tchcqv tchcqx tchcqv read (burst of 2) read (burst of 2) nop qx2 q40 q41 tchqx tchqv write (burst of 2) a0 a1 a2 a3 a4 tk#hkh tkhkh d20 d30 d31 tcq#hcqh tcqhcq#h remarks 1. q01 refers to output from address a0+0. q02 refers to output from the next internal burst address following a0, i.e., a0+1. 2. outputs are disabled (high impedance) 2.5 clock cycles after the last read (ld# = low, r, w# = high) is input in the sequences of [read]-[nop] and [read]-[write]. 3. in this example, if address a4 = a3, data q41 = d31 and q42 = d32. write data is forwarded immediately as read results.
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 20 of 34 nov 09, 2012 application example sram controller data in data out address ld# r, w# bw# sram#1 cq/cq# sram#4 cq/cq# source clk/clk# return clk/clk# zq q cq# cq sram#4 d a ld# r, w# bwx# c/c# k/k# r r v t v t r v t r v t r v t r v t r = 250 r = 250 zq q cq# cq sram#1 d a ld# r, w# bwx# c/c# k/k# r = 50 v t = v ref . . . . . . remark ac characteristics are defined at the condition of sram outputs, cq, cq# and q with termination.
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 21 of 34 nov 09, 2012 jtag specification these products support a limited set of jtag functions as in ieee standard 1149.1. test access port (tap) pins pin name pin assignments description tck 2r test clock input. all input are capt ured on the rising edge of tck and all outputs propagate from the falling edge of tck. tms 10r test mode select. this is the comm and input for the tap controller state machine. tdi 11r test data input. this is the input si de of the serial registers placed between tdi and tdo. the register placed between tdi and tdo is determined by the state of the tap controller state machine and the instru ction that is currently loaded in the tap instruction. tdo 1r test data output. this is the output si de of the serial registers placed between tdi and tdo. output changes in response to the falling edge of tck. remark the device does not have trst (tap reset). the test -logic reset state is entered while tms is held high for five rising edges of tck. the tap contro ller state is also reset on the sram power-up. jtag dc characteristics (t a = 0 to 70 c, v dd = 1.8 0.1 v, unless otherwise noted) parameter symbol conditions min. max. unit jtag input leakage current i li 0 v v in v dd ? 5.0 + 5.0 a jtag i/o leakage current i lo 0 v v in v dd q, ? 5.0 + 5.0 a outputs disabled jtag input high voltage v ih 1.3 v dd + 0.3 v jtag input low voltage v il ? 0.3 + 0.5 v jtag output high voltage v oh1 | i ohc | = 100 a 1.6 v v oh2 | i oht | = 2 ma 1.4 v jtag output low voltage v ol1 i olc = 100 a 0.2 v v ol2 i olt = 2 ma 0.4 v
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 22 of 34 nov 09, 2012 jtag ac test conditions input waveform (rise / fall time 1 ns) 0.9 v 0.9 v test points 1.8 v 0 v output waveform 0.9 v 0.9 v test points output load figure 2. external load at test tdo z o = 50 v tt = 0.9 v 20 pf 50
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 23 of 34 nov 09, 2012 jtag ac characteristics (t a = 0 to 70 c) parameter symbol conditions min. max. unit clock clock cycle time t thth 50 ns clock frequency f tf 20 mhz clock high time t thtl 20 ns clock low time t tlth 20 ns output time tck low to tdo unknown t tlox 0 ns tck low to tdo valid t tlov 10 ns setup time tms setup time t mvth 5 ns tdi valid to tck high t dvth 5 ns capture setup time t cs 5 ns hold time tms hold time t thmx 5 ns tck high to tdi invalid t thdx 5 ns capture hold time t ch 5 ns jtag timing diagram t thth t tlov t tlth t thtl t mvth t thdx t dvth t thmx tck tms tdi tdo t tlox
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 24 of 34 nov 09, 2012 scan register definition (1) register name description instruction register the instruction register holds the instru ctions that are execut ed by the tap controller when it is moved into the run-test/idle or the various data register stat e. the register can be loaded when it is placed between the tdi and tdo pins. the instruction register is automatically preloaded with the idcode instruction at pow er-up whenever the controller is placed in test-logic-reset state. bypass register the bypass register is a single bit register that can be placed between tdi and tdo. it allows serial test data to be passed throug h the rams tap to another device in the scan chain with as little delay as possible. id register the id register is a 32 bit register that is loaded with a device and vendor specific 32 bit code when the controller is put in capture- dr state with the idcode command loaded in the instruction register. t he register is then placed between the tdi and tdo pins when the controller is moved into shift-dr state. boundary register the boundary register, under the control of the tap contro ller, is loaded with the contents of the rams i/o ring when the controller is in capture-dr st ate and then is placed between the tdi and tdo pins when the controller is moved to shift-dr state. several tap instructions can be used to activate the boundary register. the scan exit order tables describe whic h device bump connects to each boundary register location. the first column defines the bit?s position in the boundary register. the second column is the name of the input or i/o at the bum p and the third column is the bump number. scan register definition (2) register name bit size unit instruction register 3 bit bypass register 1 bit id register 32 bit boundary register 109 bit id register definition part number organization id [31:28] vendor revision no. id [27:12] part no. id [11:1] vendor id no. id [0] fix bit pd46364185b 2m x 18 xxxx 0000 0000 0100 0111 00000010000 1 pd46364365b 1m x 36 xxxx 0000 0000 0100 1000 00000010000 1
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 25 of 34 nov 09, 2012 scan exit order bit signal name bump bit signal name bump bit signal name bump no. x18 x36 id no. x18 x36 id no. x18 x36 id 1 c# 6r 37 nc d15 10d 73 nc q28 2c 2 c 6p 38 nc q15 9e 74 q11 q20 3e 3 a 6n 39 q7 10c 75 d11 d20 2d 4 a 7p 40 d7 11d 76 nc d29 2e 5 a 7n 41 nc d16 9c 77 nc q29 1e 6 a 7r 42 nc q16 9d 78 q12 q21 2f 7 a 8r 43 q8 11b 79 d12 d21 3f 8 a 8p 44 d8 11c 80 nc d30 1g 9 a 9r 45 nc d17 9b 81 nc q30 1f 10 q0 11p 46 nc q17 10b 82 q13 q22 3g 11 d0 10p 47 cq 11a 83 d13 d22 2g 12 nc d9 10n 48 vss 10a 84 dll# 1h 13 nc q9 9p 49 a 9a 85 nc d31 1j 14 q1 10m 50 a 8b 86 nc q31 2j 15 d1 11n 51 a 7c 87 q14 q23 3k 16 nc d10 9m 52 a 6c 88 d14 d23 3j 17 nc q10 9n 53 ld# 8a 89 nc d32 2k 18 q2 11l 54 nc bw1# 7a 90 nc q32 1k 19 d2 11m 55 bw0# bw0# 7b 91 q15 q24 2l 20 nc d11 9l 56 k 6b 92 d15 d24 3l 21 nc q11 10l 57 k# 6a 93 nc d33 1m 22 q3 11k 58 nc bw3# 5b 94 nc q33 1l 23 d3 10k 59 bw1# bw2# 5a 95 q16 q25 3n 24 nc d12 9j 60 r, w# 4a 96 d16 d25 3m 25 nc q12 9k 61 a 5c 97 nc d34 1n 26 q4 10j 62 a 4b 98 nc q34 2m 27 d4 11j 63 a nc 3a 99 q17 q26 3p 28 zq 11h 64 vss 2a 100 d17 d26 2n 29 nc d13 10g 65 cq# 1a 101 nc d35 2p 30 nc q13 9g 66 q9 q18 2b 102 nc q35 1p 31 q5 11f 67 d9 d18 3b 103 a 3r 32 d5 11g 68 nc d27 1c 104 a 4r 33 nc d14 9f 69 nc q27 1b 105 a 4p 34 nc q14 10f 70 q10 q19 3d 106 a 5p 35 q6 11e 71 d10 d19 3c 107 a 5n 36 d6 10e 72 nc d28 1d 108 a 5r 109 ? internal remark bump id 10a of bit no. 48 and bump id 2a of bit no. 64 can also be used as nc. the register always in dicates low, however.
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 26 of 34 nov 09, 2012 jtag instructions instructions description extest the extest instruction allows circuitry external to the component package to be tested. boundary-scan register cells at output pins are used to apply test vectors, while those at input pins capture test result s. typically, the first test vector to be applied using the extest instruction will be shifted into t he boundary scan register using the preload instruction. thus, during the update-ir state of extest, the output drive is turned on and the preload data is driven onto the output pins. idcode the idcode inst ruction causes the id rom to be lo aded into the id register when the controller is in capture-dr mode and places the id register between the tdi and tdo pins in shift-dr mode. the idcode instruction is the default instruction loaded in at power up and any time the controller is placed in the test-logic-reset state. bypass when the bypass instruction is loaded in the in struction register, the bypass register is placed between tdi and tdo. this occurs when the tap controller is moved to the shift- dr state. this allows the board level scan path to be shortened to fac ilitate testing of other devices in the scan path. sample / preload sample / preload is a standard 11 49.1 mandatory public in struction. when the sample / preload instruction is loaded in the instruction register, moving the tap controller into the capture-dr state loads the data in the rams input and q pins into the boundary scan register. because the ram clo ck(s) are independent from the tap clock (tck) it is possible for the tap to attempt to capture the i/o ring cont ents while the input buffers are in transition (i.e., in a metastabl e state). although allowing the tap to sample metastable input will not harm the device, r epeatable results cannot be expected. ram input signals must be stabilized for long enough to meet the taps input data capture setup plus hold time (tcs plus tch). the rams clock inputs need not be paused for any other tap operation except capturing the i/o ring contents into the boundary scan register. moving the controller to shift-dr state then places the boundary scan register between the tdi and tdo p ins. sample-z if the sample-z instruction is loaded in the instruction register, all ram q pins are forced to an inactive drive state (high impedance) a nd the boundary register is connected between tdi and tdo when the tap controller is moved to the shift-dr state. jtag instruction coding ir2 ir1 ir0 instruction note 0 0 0 extest 0 0 1 idcode 0 1 0 sample-z 1 0 1 1 reserved 2 1 0 0 sample / preload 1 0 1 reserved 2 1 1 0 reserved 2 1 1 1 bypass notes 1. tristate all q pins and capture the pad values into a serial scan latch. 2. do not use this instruction code because th e vendor uses it to evaluate this product.
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 27 of 34 nov 09, 2012 output pin states of cq, cq# and q instructions control-register status output pin status cq,cq# q extest 0 update high-z 1 update update idcode 0 sram sram 1 sram sram sample-z 0 high-z high-z 1 high-z high-z sample 0 sram sram 1 sram sram bypass 0 sram sram 1 sram sram remark the output pin statuses during each instruction vary according to the control-register status (value of boundary scan register, bit no. 109). there are three statuses: update : contents of the ?update register? are output to the output pin (ddr pad). sram : contents of the sram internal output ?sram output? are output to the output pin (ddr pad). high-z :the output pin (ddr pad) becomes high impedance by controlling of the ?high-z jtag ctrl?. the control-register status is set during update-dr at the extest or sample instruction. sram capture register boundary scan register update register ddr pad sram output driver high-z jtag ctrl high-z update sram output
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 28 of 34 nov 09, 2012 boundary scan register status of output pins cq, cq# and q instructions sram status boundary scan register status note cq,cq# q extest read (low-z) pad pad nop (high-z) pad pad idcode read (low-z) ? ? no definition nop (high-z) ? ? sample-z read (low-z) pad pad nop (high-z) pad pad sample read (low-z) in ternal internal nop (high-z) internal pad bypass read (low-z) ? ? no definition nop (high-z) ? ? remark the boundary scan register st atuses during execution each instruction vary according to th e instruction code and sram operation mode. there are two statuses: pad : contents of the output pin (ddr pad) are captured in the ?capture register? in the boundary scan register. internal : contents of the sram internal output ?sram output? are captured in the ?capture register? in the boundary scan register. pad internal sram output driver update register ddr pad high-z jtag ctrl capture register sram output boundary scan register
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 29 of 34 nov 09, 2012 tap controller state diagram test-logic-reset run-test / idle select-dr-scan capture-dr capture-ir shift-dr exit1-dr pause-dr exit2-dr update-dr update-ir exit2-ir pause-ir exit1-ir shift-ir select-ir-scan 0 0 0 1 0 1 1 0 0 1 0 1 1 0 0 0 0 10 10 11 1 0 1 1 0 1 0 11 disabling the test access port it is possible to use this device without utilizing the ta p. to disable the tap controller without interfering with normal operation of the device, tck must be tied to v ss to preclude mid level inputs. tdi and tms may be left open but fix them to v dd via a resistor of about 1 k when the tap controller is not used. tdo should be left unconnected also when the tap co ntroller is not used.
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 30 of 34 nov 09, 2012 test logic operation (instruction scan) tck controller state tdi tms tdo test-logic-reset run-test/idle select-dr-scan select-ir-scan capture-ir shift-ir exit1-ir pause-ir exit2-ir shift-ir exit1-ir update-ir run-test/idle idcode instruction register state new instruction output inactive
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 31 of 34 nov 09, 2012 test logic (data scan) controller state tdi tms tdo run-test/idle select-dr-scan capture-dr shift-dr exit1-dr pause-dr exit2-dr shift-dr exit1-dr update-dr test-logic-reset instruction instruction register state idcode run-test/idle select-dr-scan select-ir-scan output inactive tck
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 32 of 34 nov 09, 2012 package dimensions item dimensions d e w a a1 a2 e 13.000.10 15.000.10 0.30 0.370.05 ? 0.05 0.10 1.350.11 0.98 1.00 (unit:mm) 0.15 0.25 1.50 0.50 s e y1 s a a1 a2 s y s x bab m s wa s wb ze zd index mark a b 1 2 3 4 5 6 7 8 9 10 11 a b c d e f g h j k l m n p r e d x y y1 zd ze b 0.50 t165f1-100-eq1 +0.10 165-pin plastic bga(13x15)
pd46364185b, pd46364365b r10ds0092ej0400 rev.4.00 page 33 of 34 nov 09, 2012 recommended soldering condition please consult with our sales offices for soldering conditions of these products. types of surface mount devices pd46364185bf1-eq1 : 165-pin plastic bga (13 x 15) pd46364365bf1-eq1 : 165-pin plastic bga (13 x 15) quality grade ? a quality grade of the products is ?standard?. ? anti-radioactive design is not implemented in the products. ? semiconductor devices have the possibility of unexpected defects by affection of cosmic ray that reach to the ground and so forth.
all trademarks and registered trademarks are t he property of their respective owners. c - 34 revision history pd46364185b , pd46364365b rev. date description page summary rev.1.00 ?11.05.19 - new data sheet rev.2.00 ?11.11.07 p8 modified comments for power on sequence rev.2.01 ?12.05.21 p3,4,5,12,31 corrected typo. rev.3.00 ?12.07.13 all addition : e**y series rev.4.00 ?12.11.09 all addition : -e33,-e33y series, lead series deletion : -e50,-e50y series
notice 1. all information included in this document is current as of the date this document is issued. such information, however, is subject to change without any prior notice. before purchasing or using any renesas electronics products listed herein, please confirm the latest product information with a renesas electronics sales office. also, please pay regular and careful attention to additional and different information to be disclosed by renesas electronics such as that disclosed through our website. 2. renesas electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of renesas electronics products or technical information described in this document. no license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of renesas electronics or others. 3. you should not alter, modify, copy, or otherwise misappropriate any renesas electronics product, whether in whole or in part . 4. descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. you are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. renesas electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. 5. when exporting the products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. you should not use renesas electronics products or the technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. renesas electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. 6. renesas electronics has used reasonable care in preparing the information included in this document, but renesas electronics does not warrant that such information is error free. renesas electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. 7. renesas electronics products are classified according to the following three quality grades: "standard", "high quality", and "specific". the recommended applications for each renesas electronics product depends on the product's quality grade, as indicated below. you must check the quality grade of each renesas electronics product before using it in a particular application. you may not use any renesas electronics product for any application categorized as "specific" without the prior written consent of renesas electronics. further, you may not use any renesas electronics product for any application for which it is not intended without the prior written consent of renesas electronics. renesas electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any renesas electronics product for an application categorized as "specific" or for which the product is not intended where you have failed to obtain the prior written consent of renesas electronics. the quality grade of each renesas electronics product is "standard" unless otherwise expressly specified in a renesas electronics data sheets or data books, etc. "standard": computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots. "high quality": transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; safety equipment; and medical equipment not specifically designed for life support. "specific": aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or systems for life support (e.g. artificial life support devices or systems), surgical implantations, or healthcare intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life. 8. you should use the renesas electronics products described in this document within the range specified by renesas electronics, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. renesas electronics shall have no liability for malfunctions or damages arising out of the use of renesas electronics products beyond such specified ranges. 9. although renesas electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. further, renesas electronics products are not subject to radiation resistance design. please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a renesas electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 10. please contact a renesas electronics sales office for details as to environmental matters such as the environmental compatibility of each renesas electronics product. please use renesas electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the eu rohs directive. renesas electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. 11. this document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of renesas electronics. 12. please contact a renesas electronics sales office if you have any questions regarding the information contained in this document or renesas electronics products, or if you have any other inquiries. (note 1) "renesas electronics" as used in this document means renesas electronics corporation and also includes its majority-owned subsidiaries. (note 2) "renesas electronics product(s)" means any product developed or manufactured by or for renesas electronics. http://www.renesas.com refer to "http://www.renesas.com/" for the latest and detailed information. renesas electronics america inc. 2880 scott boulevard santa clara, ca 95050-2554, u.s.a. tel: +1-408-588-6000, fax: +1-408-588-6130 renesas electronics canada limited 1101 nicholson road, newmarket, ontario l3y 9c3, canada tel: +1-905-898-5441, fax: +1-905-898-3220 renesas electronics europe limited dukes meadow, millboard road, bourne end, buckinghamshire, sl8 5fh, u.k tel: +44-1628-585-100, fax: +44-1628-585-900 renesas electronics europe gmbh arcadiastrasse 10, 40472 dsseldorf, germany tel: +49-211-65030, fax: +49-211-6503-1327 renesas electronics (china) co., ltd. 7th floor, quantum plaza, no.27 zhichunlu haidian district, beijing 100083, p.r.china tel: +86-10-8235-1155, fax: +86-10-8235-7679 renesas electronics (shanghai) co., ltd. unit 204, 205, azia center, no.1233 lujiazui ring rd., pudong district, shanghai 200120, china tel: +86-21-5877-1818, fax: +86-21-6887-7858 / -7898 renesas electronics hong kong limited unit 1601-1613, 16/f., tower 2, grand century place, 193 prince edward road west, mongkok, kowloon, hong kong tel: +852-2886-9318, fax: +852 2886-9022/9044 renesas electronics taiwan co., ltd. 13f, no. 363, fu shing north road, taipei, taiwan tel: +886-2-8175-9600, fax: +886 2-8175-9670 renesas electronics singapore pte. ltd. 1 harbourfront avenue, #06-10, keppel bay tower, singapore 098632 tel: +65-6213-0200, fax: +65-6278-8001 renesas electronics malaysia sdn.bhd. unit 906, block b, menara amcorp, amcorp trade centre, no. 18, jln persiaran barat, 46050 petaling jaya, selangor darul ehsan, malaysia tel: +60-3-7955-9390, fax: +60-3-7955-9510 renesas electronics korea co., ltd. 11f., samik lavied' or bldg., 720-2 yeoksam-dong, kangnam-ku, seoul 135-080, korea tel: +82-2-558-3737, fax: +82-2-558-5141 sales offices ? 2012 renesas electronics corporation. all rights reserved. colophon 1.1

▲Up To Search▲

Price & Availability of PD46364185BF1-E40-EQ1

	To Download PD46364185BF1-E40-EQ1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .